The EcoBoost's high-pressure fuel pump rides on a cam-driven follower that wears, and it gets misdiagnosed as bad injectors constantly. We diagnose it properly and replace the pump, follower and injectors as needed, at your home.
Direct-injection EcoBoosts run two fuel pumps: a low-pressure pump in the tank and a high-pressure mechanical pump (HPFP) on the engine, driven off a camshaft lobe through a bucket-style follower. That follower is the wear point. Its hardened face slowly erodes, and once it wears through, it starts machining the cam lobe itself, metal-on-metal, shedding debris into the engine oil while fuel pressure falls away.
Falling rail pressure is what the symptoms are made of: P0087 (fuel rail pressure too low), hard starting when the engine is hot and the fuel in the rail has heat-soaked, stalling or stumbling under acceleration when demand outruns what the worn pump can deliver, and a rough idle. The trap is that these symptoms mimic injector failure, and plenty of owners have paid for injectors that fixed nothing because the real problem was the pump and follower behind them.
The repair order matters: pull the HPFP, inspect the follower and the cam lobe under it. Caught early, it's a pump and follower. Caught late, after the lobe is wiped, the job grows into camshaft work. Injectors get tested and replaced based on evidence, not guesswork.
If your Ford is doing any of these, this is the likely cause:
Not certain that's what you're dealing with? Match the symptom in plain English first:
Or describe it to the AI mechanic, it'll tell you the likely cause for your exact Ford in seconds, free.
See how that range compares across Mississauga, Oakville, Milton, Brampton and Etobicoke in the GTA Repair Price Index, honest shop & dealer ranges for the jobs people actually get done.
High-Pressure Fuel Pump, Cam Follower & Injector Service is a big job and shops quote $1,200–$2,000 for it. The single most valuable thing you can do before committing that is have the diagnosis confirmed independently, $100–$250 flat, at your location, no hoist needed, because a diagnosis isn't the repair. Plenty of cars arrive at that quote and turn out to need the smaller version of the problem.
And the honest scoping condition, up front: once I've seen it, I tell you straight whether it's something I can do at your place. If it needs a hoist, a press or a machine shop, I say so and point you to someone who has one. I don't take a job and figure it out in your driveway. That's the whole deal, and it's why the diagnosis comes first.
What the car is doing plus what you've been quoted. Fares reads his texts between jobs.
The jobs I turn down are published, so you can check this one against the list · holding a quote already? Free quote check.
A worn follower doesn't just lose fuel pressure, it grinds hardened steel into your engine oil and eats the camshaft lobe a little more every drive. A pump-and-follower job caught early is straightforward; a wiped cam lobe is engine teardown territory. The P0087 code is the cheap warning. The expensive one is a knock.
Yes, the HPFP sits on top of the engine, making this one of the better driveway jobs on the EcoBoost. We bring everything, including live-data scan tools to verify rail pressure before and after. Most are done the same day.
Dealer pricing reflects diagnostic time plus the pump at retail, and it climbs fast if injectors get replaced on spec rather than evidence. Our model is one flat quote for the complete, correctly-diagnosed job before any work starts. You pay for the fix, not for guesses.
It happens a lot on these engines, low rail pressure from a worn pump and follower produces the exact symptoms of bad injectors. Injectors should be condemned by testing, not by symptom-matching. We check the pump, follower and live rail pressure first, because that's where this failure usually lives.
It's the hardened bucket between the camshaft lobe and the pump plunger, it takes millions of hits per tank of fuel. When its face wears through, the cam lobe starts wearing next, and that turns a bolt-on repair into engine work. It's a small part with an outsized blast radius, which is why we always inspect it and the lobe during pump replacement.
Send it over for a free second opinion. I'll tell you straight what the job actually involves, and if their quote is fair, I'll tell you that too.
Get a Free Second OpinionOther makes:
Describe it to the AI mechanic, or send it to Fares below. We come to you in Mississauga, Oakville, Milton, Brampton and Etobicoke.
Get a Flat Quote Call/Text 647-450-0406Your options on this one